Roofing squares calculator
Enter the footprint of the roof and its pitch to get the roof area in squares and the bundles of shingles that area takes.
Result
14.8 squares
45 bundles of shingles. That is 13.4 squares of roof surface plus 10% waste.
- Footprint: 1,200 sq ft
- Pitch multiplier for 6 in 12: 1.118
- Roof surface: 1,341.6 sq ft, or 13.4 squares before waste
- Shingles: 45 bundles at three bundles to the square
- Hip and ridge cap: 2 bundles for 40 feet
An estimate for a simple roof with one pitch. It does not cover starter strip, underlayment, flashing, vents, decking repair or labor, and it does not replace a roofer's measurement.
Formula
roof surface = footprint length × footprint width × pitch multiplier
squares = roof surface ÷ 100
squares with waste = squares × (1 + waste % ÷ 100)
bundles = squares with waste × 3, rounded up
cap bundles = hip and ridge length ÷ 25, rounded up
Assumptions and their sources
- One square is 100 square feet of roof surface. This is the unit roofers quote in. GAF states it in How Many Bundles of Shingles Are in a Square.
- Three bundles cover one square. The specification table on the GAF Timberline HDZ product page lists 3 bundles per square. Owens Corning gives three bundles as one roofing square of 98.4 square feet. Some heavier shingles take more than three bundles to the square, so check the wrapper of the product you are buying.
- Waste defaults to 10 percent. GAF says contractors usually include 10 to 15 percent, and Owens Corning calls 10 to 15 percent a good rule of thumb. Neither publishes separate figures for gable and hip roofs. Using 10 percent for a plain gable roof and 15 percent for a hip roof or one with valleys is this site's own assumption inside that range.
- One bundle of cap shingles covers about 25 feet. GAF's article All about Hip and Ridge Cap Shingles gives that figure for its Seal-A-Ridge product. Other cap shingles differ.
- The pitch multiplier is geometry, not a product figure. It is the length of the slope for each foot of horizontal run, from the Pythagorean theorem.
- The whole roof has one pitch and no dormers. Footprint times the multiplier gives the surface of a gable or hip roof where every plane has the same slope.
Source pages read November 16, 2026.
| Pitch | Multiplier | Roof surface over a 1,000 sq ft footprint |
|---|---|---|
| 2 in 12 | 1.014 | 1,014 sq ft |
| 3 in 12 | 1.031 | 1,031 sq ft |
| 4 in 12 | 1.054 | 1,054 sq ft |
| 5 in 12 | 1.083 | 1,083 sq ft |
| 6 in 12 | 1.118 | 1,118 sq ft |
| 7 in 12 | 1.158 | 1,158 sq ft |
| 8 in 12 | 1.202 | 1,202 sq ft |
| 9 in 12 | 1.250 | 1,250 sq ft |
| 10 in 12 | 1.302 | 1,302 sq ft |
| 12 in 12 | 1.414 | 1,414 sq ft |
Worked example
A house has a simple gable roof. Measured at the edge of the eaves, the footprint is 40 feet by 30 feet. The pitch is 6 in 12, the ridge is 40 feet long, and the waste allowance is 10 percent.
- Footprint: 40 × 30 = 1,200 square feet.
- Pitch multiplier for 6 in 12: √(1 + 0.5²) = 1.118.
- Roof surface: 1,200 × 1.118 = 1,341.6 square feet.
- Squares: 1,341.6 ÷ 100 = 13.4 squares.
- With 10 percent waste: 13.42 × 1.10 = 14.8 squares.
- Bundles: 14.76 × 3 = 44.3, rounded up to 45 bundles.
- Cap shingles: 40 ÷ 25 = 1.6, rounded up to 2 bundles.
Measuring without going on the roof
Everything this calculator needs can be measured from the ground. For the footprint, measure the outside of the house along the ground and add the overhang at each side. The overhang is the horizontal distance the roof edge sticks out past the wall. Pitch can be read from inside an attic by holding a level against a rafter: mark 12 inches along the level and measure straight up from that mark to the underside of the rafter. That height in inches is the pitch. Building plans, if you have them, state it directly.
Do not climb onto a pitched roof to measure it. Work at height on a roof belongs to an insured roofer, and a roofer measuring for a quote will take exact dimensions anyway.
How to use the result with a quote
A roofing quote is normally priced per square, so the number of squares is the first thing to compare. If a quote lists noticeably more squares than this estimate, ask how the roof was measured and what waste allowance was used. There is often a good reason. Dormers, valleys, a second pitch over a porch and a complicated hip layout all add surface and offcuts that a footprint calculation misses.
A higher waste figure is not padding on a complicated roof. Every hip and valley means shingles cut at an angle, and both GAF and Owens Corning note that waste varies with the roof.
What this estimate does not cover
- Starter strip along the eaves and rakes, underlayment, ice barrier, drip edge and flashing.
- Vents, pipe boots and skylight kits.
- Tear-off, disposal and any replacement of damaged roof decking.
- Roofs with more than one pitch, dormers or large valleys.
- Metal, tile, slate and other materials that are not sold in three-bundle squares.
- Prices and labor.